uf200-005 thru uf200-06 page: 1 frontier electronics corp. 667 e. cochran street, simi valley, ca 93065 tel: (805) 522-9998 fax: (805) 522-9989 e-mail: frontiersales@frontierusa.com web: http://www.frontierusa.com 20a ultra fast recovery rectifier uf200-005 thru uf200-06 features z dual rectifier construction, positive center tap z plastic package has underwriters laboratory flammability classification 94v-0 z glass passivated chip junctions z super fast recovery times, high voltage z low forward voltage, high current capability z low thermal resistance z low power loss, high efficiency z high temperature soldering guaranteed: 260 c / 0.17? (4.3mm) from case for 10 seconds mechanical data z case: jedec to-3p molded plastic , dimensions in inches and (millimeters) z terminals: plated lead solderable per mil-std- 202, method 208 z polarity: as marked z mounting position: any z weight: 6.4 grams maximum ratings and electrical characteristics ratings at 25 c ambient temperature unless otherwise specified single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% ratings symbol uf200 -005 uf200 -01 uf200 -015 uf200 -02 uf200 -03 uf200 -04 uf200 -05 uf200 -06 units maximum recurrent peak reverse voltage v rrm 50 100 150 200 300 400 500 600 v maximum rms voltage v rms 35 70 105 140 210 280 350 420 v maximum dc blocking voltage v dc 50 100 150 200 300 400 500 600 v maximum average forward rectified current see fig.1 i o 20.0 a peak forward surge current, 8.3ms single half sine-wave superimposed on rated load i fsm 250 a typical junction capacitance (note 1) c j 65 pf typical thermal resistance (note 2) r jc 2.0 /w storage temperature range t stg - 55 to + 150 operating temperature range t op - 55 to + 150 electrical characteristics (a t t a =25 c unless otherwise noted) characteristics symbol uf200 -005 uf200 -01 uf200 -015 uf200 -02 uf200 -03 uf200 -04 uf200 -05 uf200 -06 units maximum forward voltage at 10a per leg v f 1.0 1.3 1.5 v maximum dc reverse current at ta=25 c i r 10 a maximum dc reverse current at ta=100 c i r 100 a maximum reverse recovery time (note 3) t rr 35 50 ns notes: 1. measured at 1 mhz and applied reverse voltage 0f 4.0 volts 2. thermal resistance junction to case per leg mounted on heat sink 3. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a millimeters min max a b c d e f g h i j k l m n o p - 1.7 5.0 - 14.8 11.7 - - - 1.1 5.25 19.0 4.7 2.8 2.4 0.45 16.2 2.7 6.0 22.0 15.2 12.7 4.5 2.5 3.5 1.4 5.65 - 5.3 3.2 2.8 0.85 pi n 1 pin 2 pin 3 case c g p n h a b f e d k l m o 1 23 3.4
uf200-005 thru uf200-06 page: 2 ratings and characteristic curve uf200-005 thru uf200-06 +0.5a 0 -0.25a -1.0a trr 1c m set time base for 10/20 ns/cm fig. 3 -typical instantaneous forward characteristics 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 instantaneous forward voltage (v) 100 10 1.0 .1 .01 instantaneous forward current (a) uf200-03~06 uf200-005~02 average forward current (a) 20 16 12 8 4 0 25 50 75 100 125 150 175 case temperature ( o c) fig. 2 -typical forward current derating curve single phase half wave 60hz resistive or inductive load fig. 1 -test circuit diagram and reverse recovery time characteristic pulse generator ( note 2 ) (+) 25 v dc (approx) (-) d.u.t. 1 non inductive oscilloscope ( note 1 ) 50 no inductive 10 no inductive (-) (+) note: 1. rise time=7ns max. input impedance=1 mohms 22pf 2. rise time =10 ns max. source impedance=50 ohms fig. 4 -typical reverse characteristics 20 40 60 80 100 120 140 percent of rated peak reverse voltage (%) 1000 100 10 1 0.1 t j =25 o c t j =80 o c t j =125 o c instantaneous reverse current (ua) fig. 5 -typical junction capacitance .1 .2 .4 1.0 2 4 10 20 40 100 reverse voltage (v) 200 100 40 20 10 6 4 2 1 junction capacitance (pf) t j =25 o c
|
